Peplink / Pepwave Router Default Login, IP & Password Guide
SpeedFusion multi-WAN bonding routers, MAX cellular routers, and Balance enterprise gateways.
Use these verified administrative credentials and network addresses to access your Peplink / Pepwave router's local setup dashboard.
192.168.50.1192.168.1.1192.168.50.1192.168.1.1adminadminPepwave_XXXXStandard default gateway IP is 192.168.50.1 with credentials 'admin' / 'admin'.
Follow this 4-step walkthrough to access your Peplink / Pepwave management settings in less than 2 minutes.
Step 1: Connect to Network
Connect PC to LAN port on Peplink Balance or MAX unit.
Step 2: Open Web GUI or Gateway IP
Navigate to http://192.168.50.1 in your browser.
Step 3: Enter Admin Credentials
Enter 'admin' for Username and 'admin' for Password.
Step 4: Configure Settings & Save
Configure SpeedFusion VPN, multi-cellular SIM slots, and outbound routing policies.
These default credentials and IP addresses apply to the following popular Peplink / Pepwave wireless routers, mesh nodes, and modem gateways:
If the default password doesn't work or you forgot your custom administrator password, resetting the router restores all factory default settings.
- Make sure your Peplink / Pepwave router is connected to power and the power LED is solid ON.
- Locate the physical Reset pinhole button on the back or bottom panel of the unit.
- Use a straightened paperclip, SIM ejector tool, or pin to press and hold down the Reset button for 10 to 15 seconds.
- Release the button once the front panel LED indicator lights begin flashing or turn amber.
- Wait 2 to 3 minutes for the router to complete its reboot cycle.
- Reconnect to the factory default Wi-Fi network (
Pepwave_XXXX) and log in using usernameadminand passwordadmin.
Cannot reach 192.168.50.1 or 192.168.50.1 in browser
Ensure your device is connected directly to your Peplink / Pepwave router's Wi-Fi network or plugged into a numbered LAN port with an Ethernet cable. If you are connected to cellular data or an active VPN, disconnect them as they route DNS requests away from the local router gateway.
Default login password "admin" is not accepted
Check the physical sticker on the bottom or back of your Peplink / Pepwave router. Many modern models print a unique factory admin password or Wi-Fi key. If the password was changed during initial setup and forgotten, press the Reset pinhole button for 10 seconds to restore factory credentials.
Browser displays "Connection Not Private" or SSL Certificate Warning
Most local router administration consoles use self-signed SSL certificates when accessed via HTTPS (https://192.168.50.1). Click "Advanced" and select "Proceed to 192.168.50.1 (unsafe)" to continue securely to the local management dashboard.
How to discover your Peplink / Pepwave router's exact gateway IP address
On Windows, press Win+R, type "cmd", hit Enter, and run "ipconfig". Look for the "Default Gateway" IPv4 address. On Mac, open System Settings > Network > Wi-Fi > Details > TCP/IP to find the "Router" IP.
What is the default IP address and login for Peplink / Pepwave routers?
The primary default gateway IP address for Peplink / Pepwave routers is 192.168.50.1 (with fallback subnets 192.168.1.1). The default web administrative address is 192.168.50.1. Out of the box, the default username is admin and the default password is admin.
How do I log in to my Peplink / Pepwave router settings?
1) Connect your computer or phone to your Peplink / Pepwave Wi-Fi or plug into a LAN Ethernet port.
2) Open a browser and type http://192.168.50.1 or http://192.168.50.1.
3) Enter username admin and password admin.
4) Access the dashboard to configure Wi-Fi password, SSID name, port forwarding, and security settings.
How do I factory reset my Peplink / Pepwave router?
With the Peplink / Pepwave router powered ON, locate the small Reset pinhole on the rear or bottom panel. Insert an unfolded paperclip or pin and hold the button down for 10 to 15 seconds until the power and Wi-Fi LEDs start flashing. Release the button and wait 2-3 minutes for the router to reboot into factory default state.
Does Peplink / Pepwave have an official mobile app for setup and controls?
Yes, Peplink / Pepwave offers the InControl 2 Cloud available for iOS and Android smartphones. You can use it to set up new networks, monitor connected devices, run speed tests, and pause internet access.
How do I change the Wi-Fi name (SSID) and password on my Peplink / Pepwave router?
Log in to the Peplink / Pepwave admin page (http://192.168.50.1), navigate to Wireless, Wi-Fi Settings, or Basic > Wireless. Update the 2.4 GHz and 5 GHz Network Name (SSID) and set a secure WPA2/WPA3 password. Click Apply or Save to restart the wireless radios with your new settings.
Explore default login guides and IP addresses for alternative router brands: